INBOARD PROPELLER TOOLING

PROPELLER PULLER
The Dymex prop puller is completely self-contained and requires no other tools for operation.  Manufactured with Nibral and stainless steel, it will deliver years of dependable service.  Safely removes all types of 2- to 4-blade propellers from 10” to 22” diameter and up to a 2 1/4” shaft.
A)  Acme threaded lead screws for strength.
B)  Nibral arms for strength.
C)  Ball joint design for connecting ease.
PART NO. 110 DMX1224
 

                 
SKI BOAT PROP PULLER

Easy to use and rigid enough to last with Nibral strength.  Pulls props of 9” to 14” diameter from 3/4” to 1 1/8” shafts.                               
A)  Nibral arm for strength.                                          
B)  Nut to protect shaft threads.                                   
PART NO. 110 SK1                                                  
                                                       

ALGONAC PROPELLER PULLER                            
A great time-saver.  Protects the propeller, the shaft, and the bearings.  Pulls 2, 3, and 4-blade wheels (10” to 24”) quickly, without disturbing close coupled rudders.  Requires only minimum clearance between the hub and strut or stern bearings.            
PART NO. 118 model A                                                   
                                                            

for props 10” to 24” - maximum jaw opening 7”                   
PART NO. 118 model B                                                   
                                                           
for props 24” to 80” - maximum jaw opening 15”                 

PROP PULLER
Designed to help you remove a prop from a shaft quickly and easily.  Handles 2-, 3-, 4-, or 5-blade props up to 1 1/2” shafts.  Jaws open to 6 3/4”.  Constructed of our high-strength Nibral throughout, with cadmium-plated steel nuts and bolts for salt water protection.  Bolts are 5/8” x 9” long.
PART NO.  112 24120
 

SAFE-WAY PROPELLER PULLERS

Made of steel forgings and castings for maximum strength and toughness.   Zinc or cadmium
plated bolts, studs, nuts, and washers for maximum corrosion resistance.  Combination pullers
remove 2, 3, 4, and 5-blade propellers.  Four sizes to suit every popular 2 - 5 blade propeller.
Remove tight propellers safely and easily.

CAPACITY:  3-BLADES ONLY                                                   CAPACITY:   3-BLADES ONLY
Up to 20” propeller and 1 1/2” shaft                                                    Up to 28” propeller and 2” shaft
PART NO. 136 1                                                                              PART NO. 136 2
                                                                           

CAPACITY:  2, 3, 4, AND 5-BLADES                                         CAPACITY: 2, 3, 4, AND 5-BLADES
Up to 28” propeller and 2” shaft                                                   Up to 44” propeller and 3” shaft
PART NO. 136 2N                                                                       PART NO. 136 3N
                                                                    

ACCESSORIES:  FOR PROPELLERS WITH BLADES EXTENDING OVER THE END OF THE HUB                                                       
PART NO. 136 A1 (for size 1)                       

PART NO. 136 A2 (for size 2 and 2N)           
 

ACCESORIES:  FOR SMALL PROPELLERS
PART NO. 136 B1 (for size 1)

PART NO. 136 B2 (for size 2 and 2N)
 

PROPELLER SHAFT PULLER
The Algonac shaft puller is made of high quality stress-proof steel to exacting specifications of maximum protection of the
shaft threads.  It operates on the jack hammer principle.  You can pull the toughest shafts with no more lost tempers, pipe
wrench marks, or skinned knuckles.  Just install the proper size nut, loosen coupling set screws and proceed with the slide
hammer.  The new or repaired shaft can be put into the boat by reverse procedure.  The standard puller accomodates shafts
from 1” through 1 1/2”.  Optional nuts for 3/4” and 7/8” shaft available.
PART NO. 118 PS
 

STRUT BEARING PULLER                              
Strut bearing puller eliminates the removal of the strut from the boat or the hard pushing or sawing of the old
bearing.  Just select the proper bushing and screw the old bearing out.  Reverse the procedure and pull the   
new bearing into place.  The puller is designed to remove and install strut bearings from 1 1/2” O.D. to 2” O.D.
PART NO. 118 SB                                                 
 

TRANSMISSION COUPLING PULLER          
Flange puller with 3/4” bolt.  Grey Iron.  Fits 4” to 5” overal diameter of coupling.  Designed for 4 bolts couplings. 
PART NO. 109 MCP0050                                     
                                                    
PART NO. 109 MCP005BOLT                             
                                                    

PACKING BOX WRENCH
Ductible iron plated.  Fits rudder ports & packing boxes.

ADJUSTABLE PACKING BOX WRENCH
Adjusts from 1 3/4” to 3”.
PART NO. 112 24150
 

MARINE HYDRAULIC PULLERS
YOUR PULLER SET COMES COMPLETE AND READY FOR AN EMERGENCY.
PACKED IN A DURABLE STAINLESS STEEL CASE, EASILY STOWED UNTIL
NEEDED.  YOU’LL FIND STEP BY STEP INSTRUCTIONS WITH EACH SET.

                                                       ACCESSORIES
SIX TON RAM                           137 DMC6     -   
TEN TON RAM                         137 DMC10   -   
FIFTEEN TON RAM                 137 DMC15   -   
TWENTY FIVE TON RAM      137 DMC25   - 
   

STAINLESS STEEL PORTABLE RAM SHOP SETS

HYDRAULIC PRESS SHOP SET
REMOVES AND REPLACES STRUT BEARINGS 3/4” - 2 1/2” PROP SHAFT DIAMETER. PULLS PROPELLERS 10”-32”, 2, 3, 4 AND 5 BLADES UP TO 2 1/2” SHAFT DIAMETERS.  LEVELS ENGINES, REMOVES RUDDER QUADRANTS.  COLOR CODED AND COMPLETE WITH SIX TON RAMS, ONE FIFTEEN TON RAM, HYDRAULIC HAND PUMP AND HOSE. COMPLETE KIT SHIPPED IN ITS OWN TOOL CADDY ON WHEELS.
PART NUMBER 137 DMC1625
 

HYDRAULIC PRESS SHOP SET
REMOVES AND REPLACES STRUT BEARINGS 3/4” - 2” PROP SHAFT DIAMETER. PULLS PROPELLERS 10”-30”, 2, 3, 4 AND 5 BLADES UP TO 2” SHAFT DIAMETER.  REMOVES SHAFT COUPLINGS 7/8”-2” SHAFT DIAMETER AND LEVELS ENGINES.  INCLUDES: TWO SIX TON RAMS, ONE TEN TON RAM, HAND PUMP AND HOSE.   COMPLETELY CONTAINED IN OUR HANDY TOOL CADDY ON WHEELS.
PART NUMBER 137 DMC1612
 

                                                                  LARGER SETS AVAILABLE UPON REQUEST
                                                     HEAT TREATED ALLOY                 COMPLETELY PORTABLE
                                                     PRECISION MACHINED                    COLOR CODED COMPONENTS
                                                     RUGGED CONSTRUCTION                STAINLESS STEEL RAM
                                                                                      FIVE YEAR WARRANTY

MARINE SHAFT BEARING BLOCKS

Place a shaft on a set of Shaft Bearing Blocks and give the shaft a spin.  Visual inspection can detect .002 runout per foot.  Closer inspection with indicator may be used, but the wobble of a bent shaft is easily recognized. When a shaft is being straightened, the spring loaded ball bearings automatically press in-to the blocks.  The shaft then bears on the alloy steel V-blocks.  When pressure is released, the shaft and bearings spring back and you again have the ball bearing centers for inspection.  Simple but what a time saver.  Inspect and straighten all in one set up.

PART NO.  DMVB  7 

SET OF TWO MATCHED BLOCKS WITH TWO SOFT JAWS INCLUDED.     
STRAIGHTEN 3/4” - 2” DIAMETER SHAFT

NEW LARGER BALL BERING “V” BLOCKS
INSPECTED AND STRAIGHTENED 2” - 7” DIAMETER SHAFT ON THIS UNIQUE NEW TOOL.
PART NO.  DMVB   14


                                                                                     
     E-Mail Henry H. Smith                           Place an Order                                     Back to Index